Top 10 Ao Smith Air Pressure Switch

This is a Brand New OEM Furnace Replacement Inducer Motor Kit

2. 1 us gal (8L) in-line captive air pressure tank. Designed for water systems assembled with a jet pump. Tough epoxy-baked finish for durability. Replaceable bladder made of synthetic butyl rubber to increase reliability and life span. No water to metal contact for rust-free operation. Stainless steel flange with 1 inch NPT connection. 100 psi maximum working pressure. For use with a 20/40 psi pressure switch, the air pressure must be adjusted to 18 psi; for a 30/50 psi switch, the pressure must be adjusted to 28 psi. Drawdown 0. 7 us gal (20/40 psi); 0. 6 us gal (30/50 psi).

Product Description

At air valve, check tank air pressure with tire gauge. If needed, adjust tank pressure up or down

BODY CONSTRUCTION: Heavy Gauge Steel
BODY FINISH: Electrostatically Applied Baked-On Polyester
TANK PRECHARGE: 40 psi Nitrogen-Rich Charge
TANK CAPACITY: 35 gal
EQUIVALENCY RATING: 82 gal
DRAWEOWN WITH 20/40 SWITCH: 12.7 gal
DRAWDOWN WITH 30/50 SWITCH: 10.7 gal
DRAWDOWN WITH 40/60 SWITCH: 9.3 gal
BLADDER / WATER CELL: One Piece Seamless PVC
TANK DIAMETER: 20″
TANK HEIGHT: 36-1/4″
FLANGE: Glass-Filled Polypropylene
PIPE TAP SIZE: 1″ NPT
DISTANCE FLOOR TO TAP CENTER: 2″
MAXIMUM PRESSURE RATING: 100 PSI

From the Manufacturer

Vertical Pre-Charged pressure tank. This tank holds 35-Gallons but is equal to an 82-Gallon standard tank in performance.

Product Description

Factory pre-charge: 38 psi (pounds per square inch). maximum working pressure 100 psi. Maximum operating temperature 200 F (Degree Fahrenheit). engineered to provide years of trouble-free service using cold rolled steel for a higher strength to weight ratio. Rugged, stable steel base with protective plastic strip. Heavy-duty butyl rubber diaphragm and durable polyolefin liner to prevent corrosion. Water worker tanks feature an appliance quality finish which is resistant to sunlight and harsh conditions. All tanks are completely lead free for safety. Meets nsf (National Sanitation foundation) standard 61 for clean, safe drinking water. 5 year warranty. Blue tank.

From the Manufacturer

The WaterWorker pre-charged tanks utilize a butyl composite diaphragm, which flexes up and down based on water level and air pressure, as the pump fills the tank with water the air above the diaphragm is compressed, increasing the pressure in the tank until the pump cut-off pressure is reached. When water is drawn from the tank, the pressure inside the tank decreases until the pressure switch starts the pump. The amount of usable water for every pump cycles is called drawdown. The greater drawn-down capacity you select, the less your pump cycles saving energy, money, and extending your pump life. Advantages over galvanized well tanks: Pre-charged tanks do not have water-logging problems like the galvanized tanks. The air and water are totally separated using a diaphragm. No external air controls needed. Pre-charged tanks have a much larger draw-down for the same physical size. Larger draw down reduces pump cycles and pump wear, i.e. at 30/50 PSIG range three times the draw-down for pre-charged tanks of the same physical size. Pre-charged Tanks completely empty during each pump cycle. Pre-charged Tanks are much smaller and easier to handle that galvanized well tanks. Pre-charged tanks with a 30/50 Pressure Switch would be one-third the size of a galvanized tank with the same drawdown. Deep Well Jet Pumps could use either a vertical tank or a horizontal tank, depending on space requirements and sizing. Submersible Pump applications would usually use vertical tanks, again based on proper sizing. Shallow Well Jet Pumps could use vertical or horizontal tanks, based on proper sizing. The rule of thumb in sizing is to count the number of fixtures in the home, i.e. sinks, showers, toilets, dishwasher, faucets, washing machines, outside faucets, etc. and multiply it by 3. Example: a house with 11 fixtures x 3 would be 33-Gallon tank. We would suggest our 44-Gallon tank, which is the next larger sized tank.This is a Hazmat non-returnable item

About the Flotec FP7130 Vertical PreCharged Water System Tank 220 Gallon The Flotec FP7130 is a precharged water tank system that will save you valuable energy and space. This product was designed to give you just as much performance as conventional tanks, but in a smaller size. If you donrsquo;t mind the size of your traditional tank then you may choose to get a tank of the same size and enjoy higher efficiency. The Flotec FP7130 is a 220 gallon tank that will make your life a little easier and last for a long time to come. This product features a replaceable air and water separator for easy maintenance and is as easy to install as can be. Yoursquo;ll have it set up in no time and once you do you can enjoy years of use thanks to the durable materials from which itrsquo;s made. The Flotec FP7130 is made of heavy gauge steel with a tough outer surface that makes it tough and able to take on the damage that typically arises after years of use. You wonrsquo;t need to worry about replacing it anytime soon and yoursquo;ll be happy for that because this is a tank yoursquo;ll want to keep around for as long as possible.Please note: This tank has a rated size of 220 gallons; the actual tank capacity is 85 gallons.Caution: Using this vertical pressure tank in a horizontal position may cause it to not operate properly.

Product Description

The Pentair Superflo single-speed, 1-1/2-horsepower moves more water more efficiently for lower operating cost and super-quiet operation. Plus, by performing with less effort, there’s simply less wear and tear and that means longer life for a higher return on your pump investment. Specifically designed for in ground pools, the Superflo features thick walled body parts, a heavy-duty 56 square flange motor, and highly engineered hydraulics. SuperFlo’s silent running capability and small footprint allow it to easily drop into a compact equipment pad. The Cam and Ramp lid locks in place with a quarter-turn. SuperFlo is a direct replacement for the Hayward Super Pump.

The SuperFlo high performance pump meets all the criteria for a superior pool, spa or water feature pump. It’s super energy-efficient, super quiet and super easy to maintain. Plus, it’s designed with innovative materials that will stand up to the most demanding installations and conditions. This pump is self-priming for quick, easy start-up and has been performance and pressure tested to ensure superior quality. This is the single-speed, 1-½-horsepower, 115/230 voltage, 16.0/8.0 full load amp, standard efficient model with unionized fittings (1-1/2-inch internal slip and 2-inch external slip). It is UL/CUL/NSF certified and comes with a one-year limited warranty.

From the Manufacturer

The SuperFlo Pumps are a product of nearly 50 years of innovative hydraulic engineering. The result is an ability to move more water more efficiently for lower operating cost and super-quiet operation. Plus, by performing with less effort, there’s simply less wear and tear – and that means longer life for a higher return on your pump investment.

Impeller: F. D. A. compliant, glass filled Noryl. Corrosion and abrasion resistant. Diffuser (Guide vane): Bolt down Lexan diffuser has stainless wear ring for extended performance in abrasive conditions. Powered for Continuous Operation: Pump ratings are within the motor manufacturer’s recommended working limits. Can be operated continuously without damage. Corrosion Resistant: Electro-coat paint is baked on. Protected Mechanical Seal: Diaphragm retains water in the casing to ensure the mechanical seal can never run dry. Excellent Air Handling Ability: After initial priming the pump has the ability to re-prime itself. APPLICATIONS Specifically designed for: Homes Farms Cottages Booster service SPECIFICATIONS Pump: Pipe connections: 1¼” NPT suction, 1″ NPT discharge, 1″ NPT drive (pressure) Pressure switch: AS4 preset at 30-50 PSI Motor: NEMA standard 60 Hz 1/2 HP, 115/230 V capacitor start Single phase 3500 RPM Built-in overload with automatic reset Stainless steel shaft Rotation: clockwise when viewed from motor end UL778 listed Maximum temperature: 140°F Pressure regulator included. Pumps are manufacturer tested and may contain water inside from such testing

From the Manufacturer

Vertical Pre-Charged pressure tank. This tank holds 50-Gallons but is equal to an 120-Gallon standard tank in performance.